The TankTruss brand has been chosen by Handyman club of America to be sent through their rigorous 1,000 handyman test process. Check it out at stuffstuff.com
Featured Video
Fits Most Toilets- Easy to Install
- Helps Avoid Damage
& Service Calls - Saves Time & Hastle
Also Available at participating
The Tank Truss is a toilet tank support which helps prevent tank wobble and damage from unwanted toilet movement. It’s affordable one time insurance policy against costly leaks and repairs that every toilet should have.
A toilet tank has simple bolts and gaskets attaching the tank to the bowl. When the tank is moved, the bolts and gaskets flex, which results in anywhere from a small drip to a crack in the tank that can cause disastrous flooding.
The Tank Truss is a support system between the wall and toilet tank that prevents unwanted tank wobble and damage. It’s a simple, DIY product that can be installed in 2 minutes and it only requires a utility knife so you can cut it to properly fit between your wall and toilet tank.
News
TankTruss now has the toilet tank stabilizer available at participating ACE Hardware stores
Customer Testimonials
“Peace of mind...The Toilet Tank Stabilizer by TankTruss is a fail-safe at our shop. When we walk away from a job we don't have to worry anymore about someone calling back from a leak in the toilet tank or a crack in the tank that we previously repaired.”
—Roger Vadnais Plumbing
White Bear Lake, Mn
“We've installed the TankTruss toilet tank stabilizer on all of the toilets in our rental properties!”
—R4 Properties
“After a $20,000 insurance claim and being forced to live in a trailer for 2 weeks due to a cracked toilet tank, we installed a TankTruss set on every toilet in our house and cabin.”
—Marcia Magistad
Installation Instructions
Tools Needed
Saw or Utility Knife and Marker.
Saw or Utility Knife and Marker.
Measure
Remove lid. Place flat end of extension on the wall over the top right or left edge of the toilet tank. With a marker, mark the extension where it meets the back edge of the tank.
Remove lid. Place flat end of extension on the wall over the top right or left edge of the toilet tank. With a marker, mark the extension where it meets the back edge of the tank.
Cut
Use a utility knife to cut the thin wall of the extension down to the bottom of the base in a straight line. Cut the extension long, and trim as needed.
Use a utility knife to cut the thin wall of the extension down to the bottom of the base in a straight line. Cut the extension long, and trim as needed.
Snap
With both hands, slowly snap the extension at the cut point.
With both hands, slowly snap the extension at the cut point.
Assemble
Insert the cut end of the extension into the T-grove in the clip.
Insert the cut end of the extension into the T-grove in the clip.
Install
Clip the two assembled parts onto the back edge of the toilet tank at the locations you measured from. Replace tank cover.
Clip the two assembled parts onto the back edge of the toilet tank at the locations you measured from. Replace tank cover.
Frequently Asked Questions
Is this a Do It Yourself product?
Yes, if the simple installation process is correctly followed, the installation is fast and easy.
How do I know if I need a TankTruss product?
If your toilet has any gap whatsoever between the tank and the wall there is possibility for movement to occur in the tank. This movement is what causes leaks in the bolts and the TankTruss will stop the wobble and movement from occurring.
How long does the toilet tank stabilizer take to install?
A few minutes. Follow the instructions on above or watch the YouTube video named "toilet tank stabilizer by TankTruss" and the installation should be seamless.
Is the TankTruss Universal?
The TankTruss toilet tank stabilizer should fit most toilets but the range is .25" - 3.25" gap size. If the space is too large, either the wrong toilet was used, or the pipe was roughed in too far from the wall.
Contact Us
1-800-699-VADCO | 4786 Bald Eagle Ave St. Paul, Mn 55110
